Mining crushers — jaw crushers, cone crushers, and roll crushers — represent some of the most mechanically demanding environments in heavy industry. They impose extreme impact loads, high starting torques, and continuous vibration on every drive component. The 웜 기어 감속기 deployed in crusher auxiliary and feeder drives delivers high reduction ratios in a compact envelope, ensuring full drive torque from a standard motor frame even in the space-constrained confines of a mine shaft or processing plant.
While the primary crusher drive may use a direct-drive or fluid coupling arrangement, worm gearboxes serve critical roles in the crusher circuit: driving the vibrating grizzly feeder that regulates ore feed rate, actuating the CSS adjustment mechanism, driving the lubrication oil pump motor on large gyratory crushers, and controlling the apron feeder beneath the jaw crusher discharge.
In all these roles, the worm reducer’s defining advantage is torque multiplication at compact size — reduction ratios up to 100:1 from a single stage allow a small motor to overcome the starting inertia and shock loads characteristic of crusher circuits.
In a typical crusher plant layout, worm gearboxes appear at multiple points in the circuit:
Material specifications for crusher duty: Worm shaft in carburised-and-quenched alloy steel (HRC 60–62). Worm wheel in special alloy bronze with higher tin content for improved impact resistance. Housing in ductile iron GGG40 with IP65 sealing as minimum — IP66 recommended near crusher discharge zones where water-and-fines slurry splashing is common.
Shock load and service factor: Crusher circuits are classified as heavy-shock applications with service factor SF=1.75–2.0. This means the gearbox must be selected with a rated output torque at least 1.75× the calculated application torque. Undersizing a worm gearbox in a crusher circuit leads to premature bronze wheel wear and thermal overload.
아래 표를 사용하여 적절한 모델을 선택하십시오. 주요 매개변수에는 감속비, 출력 토크, 축 치수 및 하우징 재질이 포함됩니다. 항상 올바른 값을 적용하십시오. 서비스 팩터(SF) 사용률에 따라 다릅니다.
| 매개변수 | 일반적인 범위/값 | 선택 참고 사항 |
|---|---|---|
| 비율 | 20:1 – 100:1 recommended | Higher ratios for very slow feeder or actuator drives |
| Output Torque (SF=1.0) | Up to 4,200 N·m | Apply SF 1.75–2.0 for crusher circuit selection |
| 입력 샤프트 | IEC B5/B14 flange | IEC 60034 — direct-mount to standard motors |
| Output Shaft | 25 – 50 mm solid or hollow bore | Hollow bore recommended for direct roll-crusher shaft coupling |
| 주택 자재 | 연성 주철 GGG40 | Mandatory for shock-load crusher circuit service |
| Bearing Type | Taper roller (input + output) | Required for combined radial/axial load in crusher duty |
| 보호 등급 | IP65 minimum; IP66 preferred | Near crusher discharge and slurry zones specify IP66 |
► 서비스 팩터(SF): Uniform load SF=1.0 | Moderate shock SF=1.25–1.5 | Heavy shock / 24 h continuous SF=1.75–2.0
► 주변 온도: Standard units rated –10°C to +40°C. Australian high-ambient sites (>45°C) require high-temperature lubricant and 15% thermal derating.
Available in frame sizes 025 through 150. Single-stage reduction ratios 5:1 to 100:1. Output torque up to 4,200 N·m. Aluminium or ductile iron housing. IEC B5/B14 motor flange. IP65 standard, IP66/IP67 optional. Synthetic or mineral oil lubrication.
고객 불편 사항: A Kalgoorlie gold mine experienced monthly worm wheel failures. The original gearbox had been sized at SF=1.0 — adequate for uniform load but unable to handle impact torques when large ore blocks fell onto the apron pans.
해결책: NRV-130 worm gearbox (ratio 60:1, SF=2.0 selected output torque 2,800 N·m, taper roller bearings, IP66) replaced the undersized unit. A misalignment issue in the apron chain was also corrected.
결과: Worm wheel life extended from 4–6 weeks to over 18 months. Annual saving approximately $14,000 in parts and labour.
고객 불편 사항: A sandstone quarry’s grizzly feeder drive was producing excessive vibration transmitted through the gearbox housing to the motor frame, causing terminal connection loosening and brush wear on the slip-ring motor.
해결책: NMRV-110 worm gearbox with anti-vibration mounting feet and flexible coupling between motor and gearbox input shaft. Worm meshing geometry absorbs torsional shock better than helical gears.
결과: Motor terminal re-tightening interval extended from 4 weeks to 18 months. Slip-ring brush life doubled.
고객 불편 사항: The CSS adjustment actuator on a large secondary cone crusher was too fast — operators were overshooting target CSS by up to 5 mm due to inertia in the hydraulic adjustment system.
해결책: A two-stage tandem NMRV worm gearbox (combined ratio 3,200:1) was installed, giving precise incremental CSS adjustment with positional resolution of 0.2 mm per motor revolution.
결과: CSS setting accuracy improved to ±0.5 mm. Product size P80 consistency improved by 12%, reducing oversize recirculation by 8% and increasing plant throughput.
NMRV / NRV series worm gearboxes — frame sizes 025 to 150, manufactured to ISO 9001:2015
20년 이상의 제조 경력
2003년부터 ISO 인증을 받은 생산 시설을 보유하고 있으며, 웜 기어박스를 60개국 이상에 수출하고 있습니다.
원격 기술 지원
호주 시간대를 초월한 화상 통화 진단. 현장 방문 없이 신속한 대응.
OEM/ODM 맞춤 제작
비표준 샤프트, 중공 내경, 맞춤형 플랜지 및 비율. 전체 도면 검토 가능.
공장 직판 가격
유통 마진 없음. 투명한 대량 구매 가격으로 반복 주문 시 상당한 할인 혜택 제공
재고 보유 및 빠른 배송
표준 NMRV/NRV 프레임은 창고 재고로 보유하고 있습니다. 긴급 주문은 특급 배송으로 처리됩니다.
저희 엔지니어들은 귀사의 용도에 맞는 최적의 웜 기어박스 모델, 기어비, 축 구성 및 장착 방식을 추천해 드릴 준비가 되어 있습니다.