Screw feeders transfer bulk material from a hopper or silo outlet to the next process stage at a controlled volumetric rate. The drive unit must deliver stable, low-speed torque continuously, accommodate the variable resistance as material compacts and arches in the hopper throat, and maintain set speed without hunting. The worm gear drive is the industry-standard drive for screw feeders due to its compact single-stage high reduction, right-angle output, and ability to maintain exact output speed under variable load without electronic correction.
In Australian mining, cement, and chemical processing, screw feeders handling fine abrasive powders — iron ore fines, cement raw meal, fly ash, lime — require drive units completely sealed against ingress. The worm gearbox’s low-profile sealed housing and standard IP65 protection make it the correct choice for dusty material handling environments.
The compact form factor of worm gearboxes — with output shafts available in solid and hollow bore configurations — adapts directly to the screw feeder’s central tube structure, enabling shaft-through mounting without external couplings that could become packed with process material.
Worm gear drives appear throughout the screw feeder circuit in processing plants:
Material specification for screw feeder service: Worm shaft in carbon steel with surface hardening and precision-ground helical thread. Worm wheel in cast phosphor bronze — critical for the sustained sliding contact typical of screw feeder operation. Housing in grey cast iron with heat dissipation fins. Sealed input and output penetrations to IP65.
Selection principle: Screw feeder drives are classified as uniform-load continuous duty (SF=1.0 for standard; SF=1.25 for feeders handling material that may compact). Output speed is typically 2–20 RPM for volumetric feeders and 20–80 RPM for transfer screws.
아래 표를 사용하여 적절한 모델을 선택하십시오. 주요 매개변수에는 감속비, 출력 토크, 축 치수 및 하우징 재질이 포함됩니다. 항상 올바른 값을 적용하십시오. 서비스 팩터(SF) 사용률에 따라 다릅니다.
| 매개변수 | 일반적인 범위/값 | 선택 참고 사항 |
|---|---|---|
| 비율 | 20:1 – 100:1 | Covers output speeds 14–70 RPM at 1,400 RPM motor input |
| 출력 토크 | 10 – 4,200 N·m | Frame 025–150; confirm SF before frame selection |
| 입력 샤프트 | IEC 60034 B5/B14 flange | Direct-mount to 4-pole standard motors |
| Output Shaft | Solid or hollow bore | Hollow bore enables direct screw shaft pass-through |
| 주택 자재 | Grey Iron with fin casting | Thermal management for continuous low-speed operation |
| 매끄럽게 하기 | Oil bath, standard mineral ISO VG 220 | Synthetic PAO for 24-hour continuous duty |
| 보호 등급 | IP65 표준 | Critical for fine powder and dust environments |
► 서비스 팩터(SF): Uniform load SF=1.0 | Moderate shock SF=1.25–1.5 | Heavy shock / 24 h continuous SF=1.75–2.0
► 주변 온도: Standard units rated –10°C to +40°C. Australian high-ambient sites (>45°C) require high-temperature lubricant and 15% thermal derating.
Available in frame sizes 025 through 150. Single-stage reduction ratios 5:1 to 100:1. Output torque up to 4,200 N·m. Aluminium or ductile iron housing. IEC B5/B14 motor flange. IP65 standard, IP66/IP67 optional. Synthetic or mineral oil lubrication.
고객 불편 사항: A cement plant’s limestone silo screw feeder was overheating during the 22-hour daily operating cycle — housing temperature reaching 92°C and tripping the motor protection relay at hour 18 of each shift.
해결책: Upgraded from an undersized NMRV-063 to NMRV-090 (same ratio 40:1) with synthetic PAO ISO VG 320. The larger frame reduced equilibrium operating temperature by 18°C. A partially clogged outlet adding 35% to running torque was also cleared.
결과: Housing temperature stabilised at 67°C during the full 22-hour shift with no thermal trips. The synthetic lubricant oil change interval extended to 5,000 hours.
고객 불편 사항: A water treatment plant’s lime dosing screw feeder was producing inconsistent dose rates — gearbox output varying ±4 RPM around the setpoint due to backlash, causing pH control instability in the clarifier circuit.
해결책: NMRV-040 worm gearbox (ratio 60:1) replaced the helical unit. Worm mesh eliminates backlash at low speeds, reducing speed variation to below ±0.2 RPM at the 8 RPM setpoint.
결과: Clarifier pH consistency improved from ±0.3 pH to ±0.05 pH. Lime consumption reduced by 7% through more precise dosing.
고객 불편 사항: A grain storage facility’s 30° inclined auger was allowing grain to roll back through the auger flights after each operational stop. A separate backstop ratchet mechanism was jamming on fine grain particles.
해결책: NMRV-063 worm gearbox (ratio 40:1, IP65, food-grade H1 lubricant) replaced the open helical gearbox and ratchet combination. The worm self-lock prevented any rollback on stop.
결과: Grain rollback eliminated entirely. The ratchet mechanism and its quarterly maintenance requirement were removed from the site maintenance schedule. The same model was subsequently installed on seven further auger points at the facility.
NMRV / NRV series worm gearboxes — frame sizes 025 to 150, manufactured to ISO 9001:2015
20년 이상의 제조 경력
2003년부터 ISO 인증을 받은 생산 시설을 보유하고 있으며, 웜 기어박스를 60개국 이상에 수출하고 있습니다.
원격 기술 지원
호주 시간대를 초월한 화상 통화 진단. 현장 방문 없이 신속한 대응.
OEM/ODM 맞춤 제작
비표준 샤프트, 중공 내경, 맞춤형 플랜지 및 비율. 전체 도면 검토 가능.
공장 직판 가격
유통 마진 없음. 투명한 대량 구매 가격으로 반복 주문 시 상당한 할인 혜택 제공
재고 보유 및 빠른 배송
표준 NMRV/NRV 프레임은 창고 재고로 보유하고 있습니다. 긴급 주문은 특급 배송으로 처리됩니다.
저희 엔지니어들은 귀사의 용도에 맞는 최적의 웜 기어박스 모델, 기어비, 축 구성 및 장착 방식을 추천해 드릴 준비가 되어 있습니다.