Worm Gearbox for Butterfly Valve and Gate Valve Actuators

Worm Gearbox for Butterfly Valve and Gate Valve Actuators

Water supply and wastewater networks in Australian cities and regional infrastructure rely on thousands of manually and automatically operated valves for flow control, isolation, and pressure management. For valves of DN250 and above, a worm gearbox actuator is the industry-standard mechanism for mechanical advantage multiplication, enabling one operator or a small electric motor to generate the high operating torque needed to move large valve discs or gates against full pipeline pressure.

The worm gearbox serves two roles in valve actuation: it multiplies the input torque by the reduction ratio, and it mechanically locks the valve disc in its commanded position between operations. This second function — the inherent self-lock — is critical in water infrastructure, where valve position instability under pipeline pressure fluctuations could cause uncontrolled flow surges or water hammer events.

Australian water utility specifications — Water Services Association of Australia standards, state utility specifications including Sydney Water, Melbourne Water, SA Water, and Water Corporation WA — routinely specify worm gear actuators for butterfly, gate, and sluice valve installations in transmission mains, treatment plants, and pumping stations.

Ứng dụng và trường hợp sử dụng trong ngành

In the water and wastewater sector, worm gearboxes are deployed across the full range of valve types and sizes:

• Butterfly valve actuators — DN250 to DN2400 — from reticulation mains to large trunk main isolation
• Sluice gate actuators — water treatment plants — slow precise opening of sedimentation basin inlet/outlet gates
• Gate valve handwheel gearboxes — transmission mains — mechanical advantage for manual operation
• Check valve dashpot drives — controlled closing rate for water hammer protection
• Flow control valve motorised actuators — pumping stations — automated pressure zone management

Material specification for water/wastewater service: Worm shaft in stainless steel 316 — essential for resistance to chloride-bearing water in coastal treatment plants and to the chlorine residual in potable water systems. Worm wheel in cast phosphor bronze — self-lubricating, corrosion-resistant, with excellent durability at 0.2–2 RPM output speeds typical of large valve actuators. Housing in stainless steel 316 for coastal environments; ductile iron with epoxy lining for inland freshwater installations.

AS compliance: Worm gearboxes for valve actuators in Australian water infrastructure must meet dimensional compatibility requirements per AS 4795 (butterfly valves) and AS 2638 (gate valves). Our hộp số trục vít are available with ISO 5211 actuator mounting flanges — the interface standard referenced by AS 4795 — ensuring direct compatibility with all major butterfly valve brands used in Australian water projects.

Thông số kỹ thuật và hướng dẫn lựa chọn

Sử dụng bảng bên dưới để xác định kiểu máy phù hợp. Các thông số chính bao gồm tỷ số truyền giảm, mô-men xoắn đầu ra, kích thước trục và vật liệu vỏ. Luôn luôn áp dụng đúng phương pháp. Hệ số dịch vụ (SF) cho chu kỳ làm việc của bạn.

► Hệ số dịch vụ (SF): Uniform load SF=1.0  |  Moderate shock SF=1.25–1.5  |  Heavy shock / 24 h continuous SF=1.75–2.0

► Nhiệt độ môi trường xung quanh: Standard units rated –10°C to +40°C. Australian high-ambient sites (>45°C) require high-temperature lubricant and 15% thermal derating.

Hộp số bánh răng trục vít dòng NMRV / NRV

Available in frame sizes 025 through 150. Single-stage reduction ratios 5:1 to 100:1. Output torque up to 4,200 N·m. Aluminium or ductile iron housing. IEC B5/B14 motor flange. IP65 standard, IP66/IP67 optional. Synthetic or mineral oil lubrication.

Tiêu chuẩn tuân thủ và chất lượng

Nghiên cứu trường hợp

NMRV / NRV series worm gearboxes — frame sizes 025 to 150, manufactured to ISO 9001:2015

Tại sao nên chọn chúng tôi?

Câu hỏi thường gặp