Worm Gear Drive for Screw Feeders

Screw feeders transfer bulk material from a hopper or silo outlet to the next process stage at a controlled volumetric rate. The drive unit must deliver stable, low-speed torque continuously, accommodate the variable resistance as material compacts and arches in the hopper throat, and maintain set speed without hunting. The worm gear drive is the industry-standard drive for screw feeders due to its compact single-stage high reduction, right-angle output, and ability to maintain exact output speed under variable load without electronic correction.

In Australian mining, cement, and chemical processing, screw feeders handling fine abrasive powders — iron ore fines, cement raw meal, fly ash, lime — require drive units completely sealed against ingress. The worm gearbox’s low-profile sealed housing and standard IP65 protection make it the correct choice for dusty material handling environments.

The compact form factor of worm gearboxes — with output shafts available in solid and hollow bore configurations — adapts directly to the screw feeder’s central tube structure, enabling shaft-through mounting without external couplings that could become packed with process material.

業界における応用例とユースケース

Worm gear drives appear throughout the screw feeder circuit in processing plants:

Silo and hopper discharge screw feeders — constant low-speed material extraction against variable head pressure
Loss-in-weight feeder drive — precise rate control for batching and dosing operations
Twin-screw mixer drive — coordinated rotation of two screws at matched speeds
Inclined screw elevator — upward material transfer at angles to 45°; self-lock prevents material rollback
Rotary valve (airlock) drive — slow precision rotation of rotor between pressure zones

Material specification for screw feeder service: Worm shaft in carbon steel with surface hardening and precision-ground helical thread. Worm wheel in cast phosphor bronze — critical for the sustained sliding contact typical of screw feeder operation. Housing in grey cast iron with heat dissipation fins. Sealed input and output penetrations to IP65.

Selection principle: Screw feeder drives are classified as uniform-load continuous duty (SF=1.0 for standard; SF=1.25 for feeders handling material that may compact). Output speed is typically 2–20 RPM for volumetric feeders and 20–80 RPM for transfer screws.

Worm Gear Drive for Screw Feeders application

技術仕様および選定ガイド

以下の表を使用して、適切なモデルを特定してください。主なパラメータには、減速比、出力トルク、シャフト寸法、ハウジング材質が含まれます。常に正しいものを適用してください。 サービス係数（SF） 使用サイクルに合わせて。

パラメータ	標準範囲／値	選考ノート
比率	20:1 – 100:1	Covers output speeds 14–70 RPM at 1,400 RPM motor input
出力トルク	10 – 4,200 N·m	Frame 025–150; confirm SF before frame selection
入力シャフト	IEC 60034 B5/B14フランジ	Direct-mount to 4-pole standard motors
出力軸	Solid or hollow bore	Hollow bore enables direct screw shaft pass-through
ハウジング材	Grey Iron with fin casting	Thermal management for continuous low-speed operation
潤滑	Oil bath, standard mineral ISO VG 220	Synthetic PAO for 24-hour continuous duty
保護等級	IP65 standard	Critical for fine powder and dust environments

► サービス係数（SF）： 均一荷重SF=1.0 | 中程度の衝撃SF=1.25～1.5 | 重度の衝撃／24時間連続SF=1.75～2.0

► 周囲温度： 標準ユニットの動作温度範囲は-10℃～+40℃です。オーストラリアの高温環境（45℃以上）で使用する場合は、高温用潤滑剤と15%規格に基づく熱定格低減が必要です。

NMRV / NRVシリーズウォームギアボックス

フレームサイズは025～150までご用意。単段減速比は5:1～100:1。出力トルクは最大4,200 N·m。ハウジングはアルミニウムまたはダクタイル鋳鉄製。モーターフランジはIEC B5/B14規格。IP65標準、IP66/IP67オプション。潤滑油は合成油または鉱物油。

コンプライアンスおよび品質基準

✓ ISO 9001:2015
品質マネジメントシステム認証取得済み。すべての製品は、文書化された品質マネジメントシステムに基づき、完全なトレーサビリティを確保した上で製造および検査されています。

✓ CE認証
EU機械指令に準拠したCEマーク付き。オーストラリアおよびニュージーランドのエンジニアリングプロジェクトで広く採用されています。

✓ IEC 60034 モーターインターフェース
IEC規格のフランジおよびシャフト寸法。 主要モーターメーカー全社と直接取り付け可能。

✓ IP65 / IP66 保護等級
防塵性と高圧噴射水への耐性を備えています。オーストラリアの屋外設置における標準規格です。

事例研究

🏭

Case Study 1 — Cement Raw Mill Screw Feeder, Victoria

Cement Manufacturing
Limestone Silo Discharge Screw Feeder

顧客の課題： A cement plant’s limestone silo screw feeder was overheating during the 22-hour daily operating cycle — housing temperature reaching 92°C and tripping the motor protection relay at hour 18 of each shift.

解決： Upgraded from an undersized NMRV-063 to NMRV-090 (same ratio 40:1) with synthetic PAO ISO VG 320. The larger frame reduced equilibrium operating temperature by 18°C. A partially clogged outlet adding 35% to running torque was also cleared.

結果： Housing temperature stabilised at 67°C during the full 22-hour shift with no thermal trips. The synthetic lubricant oil change interval extended to 5,000 hours.

⚕️

Case Study 2 — Chemical Dosing Screw, Perth WA

Water Treatment Chemicals
Loss-in-Weight Lime Dosing Feeder

顧客の課題： A water treatment plant’s lime dosing screw feeder was producing inconsistent dose rates — gearbox output varying ±4 RPM around the setpoint due to backlash, causing pH control instability in the clarifier circuit.

解決： NMRV-040 worm gearbox (ratio 60:1) replaced the helical unit. Worm mesh eliminates backlash at low speeds, reducing speed variation to below ±0.2 RPM at the 8 RPM setpoint.

結果： Clarifier pH consistency improved from ±0.3 pH to ±0.05 pH. Lime consumption reduced by 7% through more precise dosing.

🌾

Case Study 3 — Grain Auger Elevator, Southern Queensland

Grain Storage
Inclined Grain Auger (30° inclination)

顧客の課題： A grain storage facility’s 30° inclined auger was allowing grain to roll back through the auger flights after each operational stop. A separate backstop ratchet mechanism was jamming on fine grain particles.

解決： NMRV-063 worm gearbox (ratio 40:1, IP65, food-grade H1 lubricant) replaced the open helical gearbox and ratchet combination. The worm self-lock prevented any rollback on stop.

結果： Grain rollback eliminated entirely. The ratchet mechanism and its quarterly maintenance requirement were removed from the site maintenance schedule. The same model was subsequently installed on seven further auger points at the facility.

NMRV / NRVシリーズウォームギアボックス - フレームサイズ025～150、ISO 9001:2015規格に準拠して製造

当社を選ぶ理由とは？

🏭

20年以上の製造実績
2003年よりISO認証取得済みの生産体制。ウォームギアボックスは60カ国以上に出荷されています。

📞

リモートテクニカルサポート
オーストラリアのタイムゾーンをまたいだビデオ通話による診断。現地訪問なしで迅速な対応が可能。

⚙️

OEM/ODMカスタマイズ
非標準シャフト、中空ボア、特注フランジ、各種比率に対応可能です。図面レビューも承ります。

💰

工場直販価格
販売代理店のマージンは一切ありません。透明性の高いボリュームディスカウントで、リピート注文で大幅な割引が受けられます。

📦

在庫あり＆迅速発送
標準的なNMRV/NRVフレームは倉庫に在庫がございます。緊急のご注文は速達便にて対応いたします。

よくある質問

▼ What output speed range is typical for a screw feeder worm gearbox?

Volumetric screw feeders typically operate at 2–30 RPM output shaft speed. Transfer screws handling bulk material over longer distances may run at 20–80 RPM. With a standard 4-pole motor (1,400 RPM input), these speeds correspond to ratios of 18:1 (for 80 RPM output) to 100:1 (for 14 RPM output). Most single-stage worm gearboxes cover 5:1 to 100:1, handling the majority of screw feeder applications with a standard motor.

▼ What is the best way to couple a worm gearbox to a screw feeder shaft?

The preferred method is a hollow bore output — the screw shaft passes through the gearbox bore and is secured with a keyway and locking collar. This eliminates the need for a flexible coupling, reduces alignment sensitivity, and prevents material from packing around a projecting coupling. Hollow bore is available on NMRV/NRV frames 030 and above.

▼ Does a worm gearbox on a screw feeder need to be self-locking?

For inclined screws (any inclination above 0°) or for screws handling sticky materials that could cause backflow, self-locking is important to prevent material rollback when the drive stops. For horizontal screws with non-cohesive dry material, self-locking is helpful but not critical. All standard NMRV/NRV worm gearboxes with ratios of 20:1 and above are self-locking under normal load conditions.

▼ What causes worm gearbox overheating on screw feeders, and how is it prevented?

Primary causes: (1) undersized frame relative to continuous thermal power rating, (2) incorrect lubricant viscosity for ambient temperature, (3) blocked housing ventilation fins, (4) elevated ambient above 40°C. Prevention: select frame size based on thermal power rating for continuous-duty applications, use synthetic PAO lubricant for 24-hour operation, and specify a frame one size larger than the torque calculation minimum for continuous-duty screw feeders in hot Australian environments.

▼ Can I use a VFD (variable frequency drive) with a worm gearbox on a screw feeder?

Yes — VFD control is fully compatible with worm gearboxes and is frequently used on dosing screw feeders to adjust feed rate without changing the gearbox ratio. When operating at reduced speed (below 600 RPM motor input), ensure adequate motor cooling — specify a forced-ventilation (FV) motor or a larger motor frame. The gearbox itself is unaffected by VFD operation and does not require any modification.

Get Free Screw Feeder Drive Sizing Assistance

当社のエンジニアは、お客様の用途に最適なウォームギアボックスのモデル、ギア比、シャフト構成、および取り付け方法をご提案いたします。

無料見積もりを依頼する
全商品を見る

詳しくはアプリケーションページまたは、当社について学ぶ会社概要ページ.

Worm Gear Drive for Screw Feeders