Worm Gear Reducer for Mining Crushers

Mining crushers — jaw crushers, cone crushers, and roll crushers — represent some of the most mechanically demanding environments in heavy industry. They impose extreme impact loads, high starting torques, and continuous vibration on every drive component. The ウォームギア減速機 deployed in crusher auxiliary and feeder drives delivers high reduction ratios in a compact envelope, ensuring full drive torque from a standard motor frame even in the space-constrained confines of a mine shaft or processing plant.

While the primary crusher drive may use a direct-drive or fluid coupling arrangement, worm gearboxes serve critical roles in the crusher circuit: driving the vibrating grizzly feeder that regulates ore feed rate, actuating the CSS adjustment mechanism, driving the lubrication oil pump motor on large gyratory crushers, and controlling the apron feeder beneath the jaw crusher discharge.

In all these roles, the worm reducer’s defining advantage is torque multiplication at compact size — reduction ratios up to 100:1 from a single stage allow a small motor to overcome the starting inertia and shock loads characteristic of crusher circuits.

業界における応用例とユースケース

In a typical crusher plant layout, worm gearboxes appear at multiple points in the circuit:

Vibrating grizzly feeder drives — eccentric mass adjustment and feed rate control
CSS adjustment actuators on cone crushers — precise low-speed setting changes under hydraulic load
Apron feeder drives beneath jaw crushers — high starting torque against loaded apron pans
Roll crusher drives (secondary stage) — low-speed high-torque direct drive of crushing rolls
Lubrication pump drives on large gyratory crushers — slow continuous pump rotation

Material specifications for crusher duty: Worm shaft in carburised-and-quenched alloy steel (HRC 60–62). Worm wheel in special alloy bronze with higher tin content for improved impact resistance. Housing in ductile iron GGG40 with IP65 sealing as minimum — IP66 recommended near crusher discharge zones where water-and-fines slurry splashing is common.

Shock load and service factor: Crusher circuits are classified as heavy-shock applications with service factor SF=1.75–2.0. This means the gearbox must be selected with a rated output torque at least 1.75× the calculated application torque. Undersizing a worm gearbox in a crusher circuit leads to premature bronze wheel wear and thermal overload.

Worm Gear Reducer for Mining Crushers application

技術仕様および選定ガイド

以下の表を使用して、適切なモデルを特定してください。主なパラメータには、減速比、出力トルク、シャフト寸法、ハウジング材質が含まれます。常に正しいものを適用してください。 サービス係数（SF） 使用サイクルに合わせて。

パラメータ	標準範囲／値	選考ノート
比率	20:1 – 100:1 recommended	Higher ratios for very slow feeder or actuator drives
Output Torque (SF=1.0)	Up to 4,200 N·m	Apply SF 1.75–2.0 for crusher circuit selection
入力シャフト	IEC B5/B14 flange	IEC 60034 — direct-mount to standard motors
出力軸	25～50mmのソリッドまたは中空ボア	Hollow bore recommended for direct roll-crusher shaft coupling
ハウジング材	ダクタイル鋳鉄 GGG40	Mandatory for shock-load crusher circuit service
ベアリングの種類	Taper roller (input + output)	Required for combined radial/axial load in crusher duty
保護等級	IP65 minimum; IP66 preferred	Near crusher discharge and slurry zones specify IP66

► サービス係数（SF）： 均一荷重SF=1.0 | 中程度の衝撃SF=1.25～1.5 | 重度の衝撃／24時間連続SF=1.75～2.0

► 周囲温度： 標準ユニットの動作温度範囲は-10℃～+40℃です。オーストラリアの高温環境（45℃以上）で使用する場合は、高温用潤滑剤と15%規格に基づく熱定格低減が必要です。

NMRV / NRVシリーズウォームギアボックス

フレームサイズは025～150までご用意。単段減速比は5:1～100:1。出力トルクは最大4,200 N·m。ハウジングはアルミニウムまたはダクタイル鋳鉄製。モーターフランジはIEC B5/B14規格。IP65標準、IP66/IP67オプション。潤滑油は合成油または鉱物油。

コンプライアンスおよび品質基準

✓ ISO 9001:2015
品質マネジメントシステム認証取得済み。すべての製品は、文書化された品質マネジメントシステムに基づき、完全なトレーサビリティを確保した上で製造および検査されています。

✓ CE認証
EU機械指令に準拠したCEマーク付き。オーストラリアおよびニュージーランドのエンジニアリングプロジェクトで広く採用されています。

✓ IEC 60034 モーターインターフェース
IEC規格のフランジおよびシャフト寸法。 主要モーターメーカー全社と直接取り付け可能。

✓ IP65 / IP66 保護等級
防塵性と高圧噴射水への耐性を備えています。オーストラリアの屋外設置における標準規格です。

事例研究

⛏️

Case Study 1 — Gold Mine Apron Feeder, Kalgoorlie WA

Gold Mining
Apron Feeder beneath Primary Jaw Crusher

顧客の課題： A Kalgoorlie gold mine experienced monthly worm wheel failures. The original gearbox had been sized at SF=1.0 — adequate for uniform load but unable to handle impact torques when large ore blocks fell onto the apron pans.

解決： NRV-130 worm gearbox (ratio 60:1, SF=2.0 selected output torque 2,800 N·m, taper roller bearings, IP66) replaced the undersized unit. A misalignment issue in the apron chain was also corrected.

結果： Worm wheel life extended from 4–6 weeks to over 18 months. Annual saving approximately $14,000 in parts and labour.

🤏

Case Study 2 — Quarry Grizzly Feeder Drive, Blue Mountains NSW

Quarrying
Vibrating Grizzly Feeder

顧客の課題： A sandstone quarry’s grizzly feeder drive was producing excessive vibration transmitted through the gearbox housing to the motor frame, causing terminal connection loosening and brush wear on the slip-ring motor.

解決： NMRV-110 worm gearbox with anti-vibration mounting feet and flexible coupling between motor and gearbox input shaft. Worm meshing geometry absorbs torsional shock better than helical gears.

結果： Motor terminal re-tightening interval extended from 4 weeks to 18 months. Slip-ring brush life doubled.

🏭

Case Study 3 — CSS Adjustment Actuator, Iron Ore Cone Crusher WA

Iron Ore Processing
Cone Crusher CSS Adjustment Drive

顧客の課題： The CSS adjustment actuator on a large secondary cone crusher was too fast — operators were overshooting target CSS by up to 5 mm due to inertia in the hydraulic adjustment system.

解決： A two-stage tandem NMRV worm gearbox (combined ratio 3,200:1) was installed, giving precise incremental CSS adjustment with positional resolution of 0.2 mm per motor revolution.

結果： CSS setting accuracy improved to ±0.5 mm. Product size P80 consistency improved by 12%, reducing oversize recirculation by 8% and increasing plant throughput.

NMRV / NRVシリーズウォームギアボックス - フレームサイズ025～150、ISO 9001:2015規格に準拠して製造

当社を選ぶ理由とは？

🏭

20年以上の製造実績
2003年よりISO認証取得済みの生産体制。ウォームギアボックスは60カ国以上に出荷されています。

📞

リモートテクニカルサポート
オーストラリアのタイムゾーンをまたいだビデオ通話による診断。現地訪問なしで迅速な対応が可能。

⚙️

OEM/ODMカスタマイズ
非標準シャフト、中空ボア、特注フランジ、各種比率に対応可能です。図面レビューも承ります。

💰

工場直販価格
販売代理店のマージンは一切ありません。透明性の高いボリュームディスカウントで、リピート注文で大幅な割引が受けられます。

📦

在庫あり＆迅速発送
標準的なNMRV/NRVフレームは倉庫に在庫がございます。緊急のご注文は速達便にて対応いたします。

よくある質問

▼ What service factor should I apply when selecting a worm gearbox for a crusher circuit application?

Crusher circuits are classified as heavy-shock applications. Apply a service factor (SF) of 1.75 to 2.0 to the calculated required output torque before selecting the gearbox frame size. For example, if your apron feeder requires 800 N·m steady-state, select a gearbox rated for at least 800 × 1.75 = 1,400 N·m. Failure to apply the service factor is the most common cause of premature worm wheel failure in crusher applications.

▼ Can a worm gearbox handle the starting torque of a crusher feeder with a loaded apron?

Yes — worm gearboxes have a starting torque advantage because sliding contact between worm and wheel provides progressive torque build-up. For heavily loaded feeders that must start against full load, specify a frame size one step larger than the running-torque calculation indicates, and confirm the motor starting torque is within the gearbox’s momentary peak torque rating (typically 2.5× continuous rated torque).

▼ What housing material should I specify for crusher applications near wet ore or slurry zones?

Ductile iron GGG40 is standard and appropriate for most crusher-circuit environments. For installations in slurry splash zones, apply an epoxy two-part anti-corrosion paint system. For highly corrosive wet slurry (acid mine drainage pH less than 4), stainless steel housing is available on request. Ensure IP66 or higher sealing is specified for slurry spray environments.

▼ How do I identify if my existing worm gearbox is under-ratio for a cone crusher CSS actuator?

Signs of under-ratio: operator overshoots target CSS by more than 2 mm per adjustment, the actuator motor overspeeds at the end of travel, or the adjustment requires multiple correction cycles. A higher ratio provides finer incremental control — we recommend a minimum 100:1 single-stage or tandem arrangement for CSS actuator drives where setting precision under 1 mm is required. Contact our applications team for a free ratio review.

▼ Can I retrofit a larger worm gearbox frame to the existing crusher feeder structure?

In most cases, yes — NMRV/NRV frame sizes are dimensionally standardised and the mounting footprint increases progressively between frames. It is common to upsize by one frame without structural modification. For larger upgrades, adapter plates machined to the existing bolt pattern are available. Our engineers can provide dimensional drawings for mounting comparison before you commit to a replacement.

Request Free Crusher Drive Selection and Sizing

当社のエンジニアは、お客様の用途に最適なウォームギアボックスのモデル、ギア比、シャフト構成、および取り付け方法をご提案いたします。

無料見積もりを依頼する
全商品を見る

詳しくはアプリケーションページまたは、当社について学ぶ会社概要ページ.

Worm Gear Reducer for Mining Crushers